PRODUCT CENTER · Full-Range Fasteners

Product Center|Full-range fastener catalog

From M0.5 micro screws to M27 cold-headed parts: insert screws, riveting & clinching, thread inserts, sealing & anti-loosening, SMT surface mount and lightweight connections. Enter through two levels — assembly method or product line — and every model page lists the specification table, applicable standards and selection basis.

6Assembly method
5 itemsSystem certifications
M0.6–M27Cold heading range
Micron-levelStraightness of extra-long parts
BY ASSEMBLY

Find products by assembly method

Threaded connection

Screwed into internal threads or thread-forming by itself, covering tool clamping, precision electronics, cosmetic parts and no-pre-tapping scenarios.

Riveting & Clinching

No welding on thin sheet: threads, grounding and support formed by press-in or blind riveting, for sheet metal, cabinets and enclosures.

Thread reinforcement

Add inserts to low-strength substrates such as aluminium, castings and plastics; the thread strength is carried by the insert, with repair capability as a bonus.

Sealing & Anti-Loosening

Two main lines — water and dust protection plus vibration anti-loosening: O-ring / pre-applied adhesive sealing, serrated / adhesive / structural anti-loosening.

SMT solder mounting

PCB board-level connections: surface-mount nuts, weld studs, high-current terminals, reflow-resistant with tape-and-reel feeding.

Lightweighting & special parts

High-strength aluminium, anti-galvanic, extra-long straightness, spring pins, adhesive bonding, UQD and special parts.

SERIES

Browse by product line

The exact dimensions, materials and applicable standards of each model are listed item by item on the series and model pages; the series keeps expanding, and structures and specifications not listed can be customized from drawings.

Insert Screws
12.9
Insert Screws

TORX® / TORX PLUS® licensed drives, class 12.9, countersunk 55°/60° and special structures, made to drawing

Riveting & Clinching
No welding
Riveting & Clinching

No welding on thin sheet: clinch nuts/studs, blind rivet studs, sealing rivet nuts, grounding clinch studs

Thread Inserts
Wire · self-tapping · key-locking
Thread Inserts

Wire thread inserts, self-tapping / key-locking / tangless inserts and aluminium / copper inserts to reinforce threads in low-strength substrates

Direct Assembly
From M0.8
Direct Assembly

Micro parts from M0.8, 0.6mm-level ultra-thin heads, PVD/CD texture finishes, inner-outer composite thread structures

Anti-Loosening
IP68 rated
Anti-Loosening

Dual sealing routes with O-rings and pre-applied adhesive: sealing bolts/nuts, sealing plugs, sealing clinch parts

SMT surface-mount fasteners
Tape & reel
SMT surface-mount fasteners

Surface-mount nuts, PCB weld studs, high-current terminals, standoffs and spacers; reflow-resistant, tape & reel packaging

ZT68 high-strength aluminium alloy
600MPa
ZT68 high-strength aluminium alloy

Class-600MPa cold-headed aluminium bolts at about 1/3 the weight of steel, for lightweight magnesium and aluminium housing connections

Adhesive bonding
No drilling required
Adhesive bonding

Adhesive bonding without drilling: large base plates and multi-tooth star bases build internal threads and locating points on composites, glass and thin sheet

Sealing Series
Self-centering
Sealing Series

Elastic interference self-centering locating, smooth assembly, no damage to hole walls during assembly and removal, three generations available

Anti-loosening
Three routes
Anti-loosening

Serrated faces, pre-applied adhesive, nylon patch, flange combos and conical washers, covering the physical / chemical / structural routes

Integrated Sealing Options
Magnesium alloys
Integrated Sealing Options

Coatings isolate the potential difference, or switch directly to 600MPa aluminium parts, dedicated for magnesium die castings

Others
No pre-tap
Others

Triangular thread-forming without pre-tapping, PT TORX pan head plastic self-tapping screws, eliminating pre-molded inserts

Extra-long high-straightness bolts
Micron-level
Extra-long high-straightness bolts

Extra-long shanks cold-headed in one piece, micron-level straightness, for motor shaft extensions and precision drive scenarios

Special parts
14.9 grade
Special parts

Shoulder screws, class 14.9 ultra-high-strength connecting rod bolts, hex flange bolts, rod ends

Cosmetic Screws
PVD
Cosmetic Screws

PVD vacuum ion coating and CD texture precision turning, colors customized to color cards

Captive screws
Stays attached
Captive screws

Retaining ring / circlip structure keeps the screw attached to the panel after removal — no lost parts when servicing enclosure covers

UQD quick couplings
UQD interface
UQD quick couplings

Quick-connect liquid cooling fittings, bidirectional self-sealing and drip-free, compatible with OCP UQD standard interfaces

ALL PRODUCTS

Browse models by series

Each group lists representative models of the series; click “Enter this series” or the dashed card to see all models of the series, or use the anchors above to jump directly to the corresponding product line.

Riveting & Clinching

Enter this series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
Riveting and clinching series
More models
Enter the “Riveting & Clinching” series to view all →

ZT68 high-strength aluminium alloy

Enter this series
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts
High-strength aluminium alloy parts

Adhesive bonding

Enter this series

Integrated Sealing Options

Enter this series
Anti-galvanic corrosion parts

Extra-long high-straightness bolts

Enter this series
Ultra-High Straightness Bolt

Special parts

Enter this series

Captive screws

Enter this series
Captive screws

UQD quick couplings

Enter this series
BUYER GUIDE

Four steps to the exact specification

1. First define the connection method: threading, riveting, insertion, SMT or bonding

For internal-thread connections that need repeated assembly and disassembly, use the threaded connection categories (insert screws / precision screws / anti-loosening / sealing). For thin sheet that cannot be welded, use riveting and clinching. If the substrate is aluminium, casting or plastic and thread strength is insufficient, use thread inserts. For PCB board-level connections, use SMT surface-mount parts. For substrates such as composites and glass that cannot be drilled, use adhesive bonding.

2. Then define the substrate and service conditions: material, potential, temperature, media

Quenched-and-tempered carbon steel parts are used for high-strength applications; in humid or chemical environments switch to stainless steel or corrosion-resistant coatings; direct contact between magnesium alloys and steel causes galvanic corrosion, so choose parts with anti-galvanic coatings or switch to aluminium fasteners; for vibration and shock, add anti-loosening structures; for water and dust protection use the sealing series and agree on the measured conditions for the protection rating.

3. Then define specifications and space: thread, head type, drive, sheet thickness

Determine the thread specification and countersink angle from the actual dimensions of the mounting hole and countersink, then select head type and drive by the available space: use ultra-thin heads or countersunk heads where space is limited, TORX PLUS® or hex socket where high torque transmission is needed, and ball plungers or spring pins where elastic locating is required. For sheet-metal parts, also confirm that the sheet thickness is within the clinching range of the corresponding model.

4. Finally define surface treatment and delivery documents

Choose black oxide, zinc plating, nickel plating, zinc-nickel, zinc-aluminium coating, PVD or pre-applied adhesive according to the service environment; corrosion resistance is agreed in terms of the neutral salt spray test of GB/T 10125. On delivery, provide material certificates, dimensional inspection and mechanical property data according to the applicable standards (GB/T 3098.1, GB/T 196/197, GB/T 17880, etc.), with salt spray and solderability tests attached when required.

MANUFACTURING

Manufacturing & Quality

01 FormingCold heading M0.6–M27

The head and shank are cold-headed in one piece so the material fibers remain continuous; extra-long shanks are likewise formed in one piece with controlled straightness, avoiding cutting the fibers by turning.

02 ThreadingThread rolling and tapping

External threads are rolled and internal threads are tapped; thread accuracy follows GB/T 196/197 and is verified with go/no-go gauges and thread gauges.

03 Heat treatmentQuenching & tempering and dehydrogenation

Quenched and tempered to the required strength class (e.g. class 12.9 with tensile strength ≥1200 MPa and hardness HRC 39–44); electroplated parts are dehydrogenated as the process requires.

04 SurfacePVD / electroplating / pre-applied adhesive

Black oxide, zinc plating, nickel plating, zinc-nickel, zinc-aluminium coating, PVD and pre-applied adhesive anti-loosening, selected by service environment and salt spray requirements.

05 TestingSeven routine test items

Material composition, dimensions, friction coefficient, salt spray, SMT solderability, hardness and tensile tests, weatherability testing; for third-party accredited items other than salt spray and weatherability, results are available in 1–2 days.

06 DeliverySupply from two nearby bases

Shenzhen Pingshan headquarters and manufacturing base, and a dedicated plant in Xiangyang, Hubei for automotive parts and high-strength aluminium, supported by a multi-regional sales network for nearby service.

07 DocumentsQuality documents with delivery

Material certificates, dimensional inspection reports, mechanical property and salt spray data; first article approval and batch traceability information are provided when required.

08 CustomizationDeveloped from drawings or samples

We provide 2D/3D drawing collaboration, a fastener database and simulation support; engineering samples are delivered in as fast as 1 day, with continuous process optimization after volume production.

ISO9001:2015IATF16949:2016ISO14001:2015ISO45001:2018IECQ QC080000:2017
FAQ

Product Center FAQ

Q1What is the relationship between product models and specifications?

This page is organized by model; a single model usually covers multiple sizes. Exact dimensions are listed item by item in the specification tables of each series page. When selecting, first confirm the structure and material on the model page, then locate the size in the series page specification table.

Q2Can specifications outside the catalog be customized?

Yes. What the page lists is the standard catalog; non-standard parts can be customized from drawings or samples, engineering samples are delivered in as fast as 1 day, and first article approval is provided before volume production; specific tolerances, materials and surface treatments follow the drawings and the order agreement.

Q3How to choose material and strength class?

Conventional carbon steel is quenched and tempered to class 12.9 (tensile strength ≥1200 MPa) for insert screws and high-clamping-force applications; class 14.9 is used for special parts such as ultra-high-strength connecting rods; stainless steels 303/304/410 are used for corrosion resistance and non-magnetic requirements; for lightweighting choose ZT68 class-600MPa aluminium bolts (about 1/3 the weight of steel). Mechanical properties are verified against the relevant clauses of GB/T 3098.1.

Q4How to choose surface treatment?

Weigh service environment against cost: black oxide or zinc plating for general indoor use; nickel plating, zinc-nickel or zinc-aluminium coating for humid and salt-spray environments; PVD and CD texture for cosmetic parts; pre-applied adhesive where anti-loosening and sealing are needed together. Corrosion resistance is evaluated by the neutral salt spray test of GB/T 10125, with the exact hours agreed per order.

Q5What quality documents can you provide?

We can provide material certificates, dimensional inspection reports, and test data on salt spray, hardness, tensile strength, friction coefficient, SMT solderability and more; our systems are certified to ISO9001:2015, IATF16949:2016, ISO14001:2015, ISO45001:2018 and IECQ QC080000:2017.

Q6How small can you go?

Micro fasteners cover M0.5–M2, the precision screw series starts from M0.8, and ultra-thin heads can reach the 0.6mm level; cold heading covers M0.6–M27, and extra-long shanks are cold-headed in one piece with controlled straightness.

Q7How do I find the category I need fastest?

Two paths: browse by assembly method (threaded connection / riveting & clinching / thread reinforcement / sealing & anti-loosening / SMT solder mounting / lightweighting & special parts) or by product line. You can also type a model or specification directly into the site search, for example M3 countersunk or M6 clinch nut.

Can't find the specification you need, or need selection advice?

Send the application scenario, substrate, thread specification and drawings to our engineers for category recommendations, samples and quotations by connection method.

All Models

Full catalogue by product line — open any model page for specifications and drawings

anti-galvanic-corrosion (2)

appearance-screws (1)

anti-loosening-series (21)

bonding-series (5)

direct-assembly (2)

high-strength-aluminum-alloy-sleeves (8)

insert-screws (13)

non-detachable-fasteners (1)

others (5)

precision-screws (13)

riveting-series (15)

sealing-series (15)

smt-fasteners (8)

spring-pins (4)

straightness-bolts (1)

uqd (1)

thread-inserts (9)

Tel: 13560730094
WeChat QR Code
CNENDEESJAPTRU